How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
Everyone maintains their private theory with regards to How to Install a Bathtub Yourself.
Setting up a tub isn't precisely brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult project. If the old bathtub is easily easily accessible, the job can move speedily; if you need to open up a wall to remove the old tub and also place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's skills, although you will require an assistant to leave the old tub and also embeded in the new one. See to it you have certified on your own for the task and fit attempting it. Rather than working with a specialist to take over a halfway-completed task, it is much better to consider using one before you begin. Opportunities are you may require an expert plumber to make tube connections.
This write-up will help you mount a new bathtub in your shower room if you have currently purchased a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools and also material list ought to consist of the following:
Preparing for the Installment
Firstly, the sustaining frame provided with the bath must be fitted (if required) according to the maker's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of both faucets using 2 nuts as well as olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of all of the supplied washers.
Attach the catch to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be fitted in its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is disconnect the supply of water. After doing so, activate the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome due to the restricted gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. When the taps have been eliminated, the holes in the bath/basin will have to be cleaned of any kind of old securing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new taps to fit.
Installing the Bathtub
Making use of both wood boards under its feet, put the bath tub in the called for placement. The wood boards are valuable in uniformly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also changing the feet on the tub until the level reviews degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the proper supply pipe by making a compression join; after that do the exact same for the other faucet.
Turn on the supply of water and examine all joints as well as new pipework for leakages as well as tighten them if required. Fill the bath tub and also examine the overflow outlet and the regular outlet for leakages.
Lastly, fix the bathroom paneling as defined in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has actually been used at least when as this will settle it right into its final position.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will require a plastic port to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in area between the tap as well as the sink. Secure the faucet in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with regular tap adapters. The former kind ought to be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bathroom fulfills the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture a rigid seal, triggering the water to pass through the wall in between the bath as well as the tiling, bring about problems with wetness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to permit the movement experienced when the tub remains in usage. The sealant can break relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We are very interested in How to Install a Bathtub and I'm hoping you appreciated my blog post. Sharing is nice. Helping others is fun. We thank you for reading our article about How to Install a Bathtub.
This Website Report this page